Lynnwood repair desk · dryer

Dryer Repair in Lynnwood, WA

An hour in the dryer and the jeans are still damp, a drum that squeals, a dryer that hums but will not turn? We repair gas and electric dryers, stacked units and ventless models in Lynnwood homes.

  • Repair cost in writing up front
  • LG and Whirlpool authorization
  • Open all week, 8 AM–7 PM, Saturday and Sunday included
Maytag front-load dryer with its cycle dial and control panel

Maytag dryer

Snapshot 1 of 9

A Maytag front-load dryer. Maytag comes under our Whirlpool authorization, so its covered repairs run through us as well.

A Samsung dryer with steam cycles and a moisture sensor. Long run times on a dryer like this send us to the vent before the heater.

An LG front-loader with the door open and the drum in view. LG is one of the two makers that authorized us, so its warranty repairs come straight to us.

A Frigidaire Professional gas cooktop with all five burners lit: short, even blue cones on every port, which is how a healthy burner looks.

A white top-freezer refrigerator. If the milk below turns warm while the ice cream up top stays hard, the coil up top has usually iced over or its fan has quit.

A stainless Kenmore side-by-side with a dispenser on the freezer door, so a water valve and a filter join the list of parts to test.

The same cooktop with the grates lifted off. The lit burner throws a lopsided flame, a sign to clean the ports and reseat the cap.

A hand runs along the door gasket of an LG washer, feeling for tears and for anything caught in the folds.

Gray residue and a rust-colored film packed into a washer door boot. That fold holds water, and it is where most front-loader smells begin.

Tap the photo for the next one

Plan a repair visit

Three quick steps. We phone back to confirm a time and to tell you the diagnostic fee, which is credited to the repair if you go ahead.

Which appliance
The problem
Contact

Your details are used only to set up the visit.

Dryers we fix

What goes wrong with a dryer

An electric dryer with no heat has usually lost its thermal fuse, its element or a worn cycling thermostat; a gas one, its igniter or valve coils. The squealing and thumping come from worn drum rollers, the idler and the belt. We test the heating circuit with a meter, check how well air leaves the machine, and quote the repair before we start.

  1. 1Tumbles but no heat

    Thermal fuse, element or high-limit on electric; igniter or valve coils on gas.

  2. 2Loads take two runs

    A restricted duct, a weak element, or sensor bars coated by dryer sheets.

  3. 3Drum stands still

    A snapped belt, an idler wheel frozen on its shaft, or a motor that only hums.

  4. 4Squeal or thump

    Worn rollers, glides or an idler bearing.

  5. 5Stops partway

    Lint blocking the airflow, a weak motor switch, or a thermostat reading wrong.

  6. 6Top too hot to touch

    Turn it off and call. That much heat means a blocked duct or a thermostat stuck closed.

In your home

Repairs where the dryer stands

A fuse that blows twice is almost never bad luck. It means the air path is restricted somewhere: a crushed foil duct behind the dryer, a long run through an attic, a hood outside packed with lint. We look at the duct during every dryer repair so the new part is not the next one to fail.

Many Lynnwood split-levels vent the dryer up through the house and out the roof, a long climb that loads with lint every winter. Townhouses built in the last twenty years often run the duct across a ceiling to a side wall. Both work, but both need cleaning more often than a short run through a basement wall.

Samsung dryer with steam cycles and a moisture sensor on its panel

Samsung steam dryer

Sensor cycles stop when two metal bars inside the drum report a dry load. Softener film on those bars can end a cycle with the towels still damp.

How it goes

From the first call to a machine that works

  1. 1

    Tell us about it

    Call, or fill in the booking card with the machine, its symptoms and your ZIP. Our office rings back to pick an hour that suits you, on any day of the week.

  2. 2

    We test first

    The technician checks the outlet or breaker, runs a cycle, and clips a meter onto the parts that match the symptom. Readings, not guesses, decide the diagnosis.

  3. 3

    You approve a written price

    You see the repair figure, in ink, before anything comes apart. Go ahead, and the trip charge melts into it; pass, and the trip charge settles it.

  4. 4

    Fixed, with paperwork

    Our vans stock the igniters, pumps, valves and fuses that fail most, so plenty of repairs end on visit one. Waiting on an ordered part? The second visit goes on the calendar before we drive off, and your invoice names the warranty period.

Pick a flag

What we fix

Seven flags on the line, one for each kind of job. Tap one, or let the line run on its own.

Illustration of a front-load dryer with a towel over the top and warm air rising
Illustration of a top-freezer refrigerator with a thermometer and a drop of water beside it
Illustration of a top-load washer with the lid open, suds rising and a sock hanging over the edge
Illustration of a dishwasher with soap bubbles and a clean plate leaning against it
Illustration of a kitchen range with a steaming pot on the cooktop and the oven light on
Illustration of an ice bucket full of cubes with a scoop resting on top
Illustration of a technician’s toolbox with a meter and a screwdriver on top

Flag 1 of 7

Dryers

Jeans still damp, a drum that squeals, a duct thick with lint.

More on dryers →
1 / 7

Questions

Dryers: what people ask

Do you clean dryer ducts?

Whatever duct we can get at gets cleared during the repair. Runs that climb to the roof belong to a duct-cleaning crew, and you will hear from us when that is the real culprit.

Is a burning smell dangerous?

A whiff after months of sitting idle is usually dust burning off. If it keeps coming back, or you find browned lint by the door, leave the dryer off and book a visit.

Can you repair gas dryers?

Yes. Igniter and coils get tested on the spot, and each gas fitting we touch is leak-checked on the way out.

Do you work on ventless dryers?

Yes, condensing and heat-pump models both. Their lint filters and condensers need rinsing, and we will show you where they sit.

Let us take a look

Give us a sentence about the trouble and your street. Our office rings you to agree on an hour and quote the trip charge; the repair figure follows in writing.

CallBook a visit